Both the front and the back of the splice should resemble the illustrations shown. 2 Eye Splice Making Cordage from Thistle Collect the stalks of thistle. When you tuck, take care to use all three strands in each round and that you tuck under a strand in the standing part of the rope and not under one of your working strands. Tighten if necessary by pulling on the strand ends. Mark this strand with a triple hash mark. and perfection loop) and two splices (three-strand eye splice and braid-on-braid. Figure 2.2 Amsteel Blue Synthetic Fiber Rope. Insert the fid to separate the strands and make this tuck, continuing to work counter to the lay or twist of the rope. Figure 2.2 shows the Amsteel Blue rope with a three-inch eye splice and the taped strands. There is one working strand left to tuck and there is one strand left in the standing part of the rope that does not have a working strand under it. Mark this strand with a double hash mark. Using the fid to separate strands, tuck the next working strand over the strand you just tucked under and under the strand just below it. Mark the first tucked strand with a single hash mark numbering the working strands will help you keep track of the tucking process. With a fid or your finger, raise a strand just below the tape on the standing part of the rope and insert the middle working strand under the fid and pull the strand through. To avoid a twist in the eye of the finished splice, untwist the rope one-half turn between the pieces of tape. Splice terminations are used in all our ropes to determine new and unused tensile strengths. Splicing a 24-strand nylon rope into a loop. Form the eye and tape the standing part of the rope. Knots can significantly decrease a ropes strength while, in most cases, splicing maintains 100 of the specified rope strength. Take out the 3-strand core rope after 6 pairs of strands of the same twist. Note Tests indicate reduced efficiency when using a 4/2 grouping of the strands as compared to a 3/3 grouping. Then bring the 3 strand + core group over the 3 strand group and down into the eye formed until their strands conform to their natural configuration. 3Measure 2 tubular fid lengths (4 wire fid lengths). Cross the second group of 3 strands over the first group of 3 strands + the core. Blandford THE INTERNATIONAL GUILD OF KNOT TYERS HJD 21/04/09 For further information about the Guild and its local branches across the world Please go to Chart No. For an 8-strand construction, mark every third left and right strand for two strands. unlay the rope up to the tape then tape the end of each strand. Eye Splice 3 Strand Rope Original Drawing By Percy W. Getting Started: From one end of the rope, countback 16 crowns. Secure the eye from slipping with small twine. Next, form the desired eye size from this mark towards the standing part of the rope. When we bought DreamChaser the anchor chain was connected to an eye screwed into the based on the Anchor Chain locker. Measure distance from end of braid and mark with marking pen. Tools Required: Fid tape or whipping twine marking pen, scissors or a sharp knife hot knife or heat source ruler. Procedure: To begin, determine the tail length needed by counting ten pics from the bitter end. Take care that the tucks lie neatly rope strength can be lost if the strands are twisted incorrectly. �Ͱv��D����M=I����Ǵ��4��ٸr����^�L1 k� �.Class 1 3-strand ropes are made from any or all of the following fibers: Olefin, Polyester, NylonĪlthough the 3-strand splice is the most common splice, and simple to perform, technique is important to preserve splice strength.
#3 STRAND EYE SPLICE PDF PDF#
Tous les documents sont accessibles \directement par les bookmarks pdf � gauche)/Type/Annot/Popup 15565 0 R/AP>endobj15563 0 obj/Type/XObject/BBox/FormType 1>stream
0 kommentar(er)
